x
 

VIEW LARGER

elfa Casters

Add our elfa Casters to any elfa Drawer Frame for increased mobility and flexibility. The adapters allow them to easily and securely snap onto the bottom of your elfa Drawer Frame. See more product details below.

  • Easy, no-tools installation
Item

Enter your zip code for product availability and pickup options at your nearest store.

or Select a Store
Quantity Price

elfa Casters Black Set of 4

3"

10051416

Available for Shipping

* Cannot be expedited

$9.99 ea

elfa Casters 4.6 5 25 25
media storage Attached the casters to an existing elfa drawer frame with drawers. Easy installation. Inserted drawer liners in the drawers and I now have a mobile media storage cart. Yay! September 5, 2013
Great wheels. Use a mallet! Once I figured out that the best way to keep the backstop pins in place on my elfa shelving was to use a tiny bit of scotch tape, the only other challenge was these casters. They have that ring around them that keeps them from going into the bracket more than a quarter inch. I banged and pushed and finally contacted customer service, who said oh yes, I needed to pound with a mallet. Which I found difficult to do since they're *wheels* and kept spinning and I didn't want to hit too hard and possibly break or crack them. I finally did it by holding the whole caster in place with my left hand and bringing the mallet down not just on the top of the wheel, but also tapping down on the edge of that plastic piece that runs through the middle. I hit harder than I wanted to but it worked. The wheels eventually go all the way in. November 21, 2012
Improved casters that rock because they ROLL I have many decades-old elfa frames with assorted drawers. Some units have casters. for mobility. However the original casters were flawed in design in that their attachment to the frame involved an L angle which offset the weight transfer from frame to floor. That angle bent under heavy weight. - like my computer printer - and severely curtailed the very purpose of casters. It was more dragging than rolling. I noticed that the new casters eliminated the weak L angle and directed any weight straight down. I tried a set and voila! I am now gradually replacing all of the bent casters with the improved design. But note: a little on-site engineering is necessary for the new adapters to fit the old elfa frames but it's nothing a well-directed hammer and a screw driver cannot achieve. Let the good times roll! April 25, 2010
sturdy At first I thought these casters were ugly. But when I put them on my assembled frame and used them I was very happy with the functional aspects. They are solid, sturdy and love that I can use them in small spaces because they swivel . And they didn't look out of place once I had them on the assembled frame. June 11, 2014

Read all reviews
5 Questions : 5 Answers

Product Q&A

Ask your questions. Share your answers.

 
 
« Back
 
 
11 months ago
Customer avatar
by
Read all my Q&A
 
Please wait while more information about JeanneB is loaded.
Additional information about JeanneB could not be loaded.
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers

Staff Answer
Answer: 
The set of wheels & the black caster bases (that hold each wheel) have changed since the 90's, but the elfa frame to which the base & wheels attach has not changed.

If you previously have wheels from the 90's and have lost one or more, you will need to remove the old set & use a complete brand new set of wheels & bases on that elfa frame.
11 months ago
Customer avatar
by
Read all my Q&A
 
Please wait while more information about mmbriscoe is loaded.
Additional information about mmbriscoe could not be loaded.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0
8 months ago
Customer avatar
by
Read all my Q&A
 
Please wait while more information about ggrec is loaded.
Additional information about ggrec could not be loaded.
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers

Staff Answer
Answer: 
The casters are about 1-1/2'' W, and they will not impact the width of your overall solution.
8 months ago
Customer avatar
by
Read all my Q&A
 
Please wait while more information about tcbeall is loaded.
Additional information about tcbeall could not be loaded.
+1point
1out of 1found this answer helpful.
Was this helpful?helpful1unhelpful0
Has staff answer
 
1 answer

height of old and new the same?

I have three 7 runner+4 runner stands all on casters from the late 90's. I want to get another 7 runner+4 runner stand with casters. Am I going to have a height issue with all four being level?
6 months ago
Customer avatar
by
Forney, TX 75126, USA
Read all my Q&A
 
Please wait while more information about bcurry is loaded.
Additional information about bcurry could not be loaded.
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers

Staff Answer
Answer: 
The elfa Casters are 3" high. The previous model of elfa casters were approximately 1/2" shorter.
6 months ago
Customer avatar
by
Read all my Q&A
 
Please wait while more information about lgmorris is loaded.
Additional information about lgmorris could not be loaded.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0
I plan to use the Platinum elfa freestanding Feet with 62" standards in my closet (3' wide) but would like to add casters to access the eave storage behind the closet. Is this possible?
6 months ago
Customer avatar
by
Arlington, VA, USA
Read all my Q&A
 
Please wait while more information about CabreyFamily is loaded.
Additional information about CabreyFamily could not be loaded.
0points
0out of 0found this question helpful.
Was this helpful?helpful0unhelpful0

Answers

Staff Answer
Answer: 
Our elfa Freestanding units are not designed to be mobile. They must either rest against a wall, or be double sided.

You may want to look into our Metro or InterMetro units as they can be designed to act as a mobile wardrobe. Please see our Product Recommendations for additional details. To have a custom unit designed, please contact our customer solutions department.
6 months ago
Customer avatar
by
Read all my Q&A
 
Please wait while more information about tcbeall is loaded.
Additional information about tcbeall could not be loaded.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0
Has staff answer
 
1 answer

Are there plans to produce these in white?

8 months ago
Customer avatar
by
Chicago, IL, USA
Read all my Q&A
 
Please wait while more information about CardsGirl is loaded.
Additional information about CardsGirl could not be loaded.
-1point
0out of 1found this question helpful.
Was this helpful?helpful0unhelpful1

Answers

Staff Answer
Answer: 
At this time, we only offer our casters in black. We do not have any further details about additional colors. We will be sure to pass your feedback along to our buying department for further review and consideration.
8 months ago
Customer avatar
by
Read all my Q&A
 
Please wait while more information about tcbeall is loaded.
Additional information about tcbeall could not be loaded.
0points
0out of 0found this answer helpful.
Was this helpful?helpful0unhelpful0
1 of 1
1 of 1

 
©2014 The Container Store® Inc.   All rights reserved. Use of this site signifies your acceptance of The Container Store® Website Privacy Rights.
California Transparency in Supply Chains Act